Std Prod PCA Bring Up.  Jumpers set.  AC In. Resistive Load.  Split Phase 1+3 (Note Tested in UK with 240V per phase)
------------------------------------------------------------------------------------------------------------------------

Settings:

// **************** DEFINE VOLTAGE REFERENCE ****************
#define ATM_SINGLEVOLTAGE false // Set to true to use V1/ATM_V1P for VoltageGain1, VoltageGain2, VoltageGain3 and Calcfulations for CT1, CT2, CT3, CT4, CTN.  (Default true)

// **************** DEFINE PHASE TYPE ****************
#define ATM_SPLITPHASE true // If Split Phase (i.e. USA 120+120), set to true else leave false (NB. Not fully tested). ATM_SINGLEVOLTAGE = false

------------------------------------------------------------------------------------------------------------------------

DitroniX IPEM-1 ATM90E32 ATM90E36 IoT Power Energy Monitor Board - Development Code

Initialise OLED (If Plugged In)

Register Status and Startup Report
IPEM-1 ATM90E32 ATM90E36 IoT Power Energy Monitor
ESP32 Serial ID: 5499FEEF49C0   Firmware Version: 230616
Board Location: House

Software Optons
----------------
Wi-Fi is Disabled
Domoticz Publishing is Disabled
MQTT Publishing is Disabled
ThingSpeak Publishing is Disabled

EEPROM Check: 20        (Validation OK)

PWM Output is Disabled

DAC Output is Disabled

Peripherals Test
-----------------
Testing RGB LED
Scanning I2C Bus for Devices ...
 * I2C device found at address Decimal 60 = Hex 0x3C OLED
 * I2C device found at address Decimal 80 = Hex 0x50 EEPROM
 * I2C Bus Scan Complete

AC/DC Voltage Input Detected
Connecting to the ATM90E32
ATM90E32 Connected - OK
IPEM Hardware Setup and Power-Up Test - Board Initialized

Register Status and Diagnostic Report
IPEM-1 ATM90E32 ATM90E36 IoT Power Energy Monitor
ESP32 Serial ID: 5499FEEF49C0   Firmware Version: 230616   Location: House

Hardware Configuration for ATM90E32
------------------------------------
AC Voltage Inputs:      Multi Dual V1 and V3 - USA Configuration
Split AC Voltage:       Dual Input V1 and V3 Enabled - USA Configuration
CT Current Clamps:      Phase Configured for 1 and 3 + 1 Phase (ESP32)
CT4 Current Input:      Configured for ESP32 ADC

[Status Values]
System Status:          S0:0x37E                S1:0xFFFE
Meter Status:           E0:0x20F                E1:0xFF

Mains RMS Voltage
------------------
Voltage 1: 248.38 V
Voltage 3: 248.04 V
- - - - - - - - - - - - - - - - - - - - - 
Total Split Voltage: 248.21 V (V1~X~V3)

Mains RMS Current
------------------
Current CT1: 0.66 A
Current CT3: 0.65 A
Actual Total Current: 1.31 A (CT1~X~CT3)

Calculated RMS Power
---------------------
Power V1*I1: 163.93 W
Power V2*I2: 0.00 W
Power V3*I3: 161.23 W
- - - - - - - - - - - - - - - - - - - - - - - -
Calculated Total Power: 325.16 W (CT1~X~CT3)

Active Power (Absorbed or Used by the Load)
--------------------------------------------
Active Power CT1: -162.96 W     (Export)
Active Power CT2: 0.00 W
Active Power CT3: -161.95 W     (Export)
- - - - - - - - - - - - - - - - - - - - -
Total Active Power: -324.91 W   (Export)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 
Calculated Total Active Power: -324.91 W (CT1~CT2~CT3)


Re-Active Power
----------------
ReActive Power CT1: -10.07 VAR
ReActive Power CT2: 0.00 VAR
ReActive Power CT3: -9.77 VAR
- - - - - - - - - - - - - - - - - - - - - - - - -
Total ReActive Power: -19.83 VAR (CT1~CT2~CT3)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Calculated Total Reactive Power: -19.84 W (CT1~CT2~CT3)

Apparent Power (Total Amount of Power Flowing from Source to Load)
-------------------------------------------------------------------
Apparent Power CT1: 163.32 VA
Apparent Power CT2: 0.45 VA
Apparent Power CT3: 162.27 VA
- - - - - - - - - - - - - - - - - - - - - - - -
Total Apparent Power: 325.62 VA (CT1~CT2~CT3)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Calculated Total Apparent Power: 326.04 W (CT1~CT2~CT3)


Other Power Information
------------------------
Total Fundamental Power: -324.36 pH(t)

Total Harmonic Power: -0.55

Power Factor
-------------
Power Factor CT1: 0.00 PF
Power Factor CT2: 0.00 PF
Power Factor CT3: 0.00 PF
- - - - - - - - - - - - - - -
Total Power Factor: 0.00 PF

Phase Angle
------------
Phase Angle CT1: 0.00
Phase Angle CT2: 0.00
Phase Angle CT3: 0.00

Other Information
------------------
Chip Temperature: 32.00 °C

Mains Frequency: 50.10 Hz

PCB Temperature Sensor (NTC_IN VN):     31.73 ºC

ADC Raw: 2770 > ADC Adjusted: 2770 > Calculated: 26.38 V